
By Rudhra Industries Engineering Team | Technically reviewed “By Rudhra Industries Engineering Team | Last reviewed: 19 November 2026”.
Industrial wastewater treatment is the process of treating factory effluent to remove pollutants such as organic load (BOD and COD), suspended solids, dissolved salts, oils and toxic chemicals to allow safe discharge or reuse. The treatment generally consists of five stages: preliminary treatment, primary physico-chemical treatment, secondary biological treatment, tertiary treatment and polishing and sludge handling. Zero Liquid Discharge (ZLD) is also added to the process when discharge is restricted. The process and the treatment combination used depend upon characteristics of the wastewater to be treated, goals of treatment, the state pollution control board (SPCB) norms and restrictions.
Table of Contents
- What Is Industrial Wastewater and Where Does It Come From?
- Why Industrial Wastewater Treatment Is Mandatory in India
- Key Wastewater Parameters: BOD, COD, TSS, TDS and pH
- Stages of Industrial Wastewater Treatment, Step by Step
- Treatment Methods: Physical, Chemical and Biological
- Treatment Technologies Compared: ASP, MBBR, SBR, MBR and UASB
- Advanced Treatment: Filtration, RO, Evaporation and ZLD
- Industrial Wastewater Treatment by Industry
- How to Choose the Right Treatment System
- Cost of Industrial Wastewater Treatment in India
- Common Problems and How to Fix Them
- Explore Our Wastewater Treatment Guides
- Why Industries Choose Deur Water a product of rudhra industries
- Frequently Asked Questions
- CTA
- Conclusion: Start With Your Effluent, Not a Technology
What Is Industrial Wastewater and Where Does It Come From?
Industrial wastewater is any water that carries pollutants out of a manufacturing or processing operation. Wastewater can be generated by a multitude of activities including washing, cooling, blowdowns, reactions, rinsing, and cleaning.
It is distinct from domestic sewage. Sewage is largely comprised of organic matter and pathogens. Industrial effluent changes with the product, the batch and even the shift. A dyehouse can send out color and salt, a pharma unit can send out solvents and active drug residue, a dairy can send out fat and milk solids, and an electroplating operation can send out heavy metals at a very low pH.
That variability is why a copy-paste design rarely works. Typical pollutant groups include:
• Organic load: measured as BOD and COD (food, dairy, distillery, pulp and paper, textile)
• Suspended solids and turbidity: fibres, fines, precipitates
• Dissolved salts (TDS): dyeing, chemical, pharma, boiler and RO reject streams
• Oil and grease: engineering, automotive, food processing
• Metals and toxics: electroplating, tanneries, chemical units
• Extreme pH and colour: textile, chemical and dye intermediates
Understanding what your own stream contains is the first step in solving it, and it is why every good treatment project starts with an effluent analysis, not a catalogue.
Why Industrial Wastewater Treatment Is Mandatory in India
It is mandatory by law to treat effluent in India under The Water (Prevention and Control of Pollution) Act, 1974 and The Environment (Protection) Act, 1986. In the former, industries have to obtain Consent to Establish (CTE) and Consent to Operate (CTO) from State Pollution Control Boards (SPCB). The conditions set in the consents defines the limits of pollutants in the discharge water.
The Central Pollution Control Board has published in the Environment (Protection) Rules, the general discharge standards for various industries, and these standards are sector specific. Some general standards for discharge to inland surface water are: pH- 5.5 to 9.0; BOD- 30 mg/L; COD- 250 mg/L; TSS- 100 mg/L; oil and grease- 10 mg/L. Always check your limitations in the consent conditions, as these vary depending on the sector, location and the receiving body.
There are serious legal and practical implications of not meeting the standards. Plants can be ordered to shut down. A business case can also be made to retrofit effluent treatment plants. In addition, there is a financial incentive to treat wastewater, as industries can be heavy users of potable water and use it for various processes, including cooling and washing. 80 to 90 percent of the water can be recycled, thus lowering costs for tanker water and potable water.
By 2026, regulators and buyers expect more from monitoring water outlets. Based on research, online monitoring of key parameters, compliance to OCEMS for notified categories, record of disposal of sludge and sustainability reports to export customers indicate that treatment plants are moving towards better automation and better documented treatment processes.
Key Wastewater Parameters: BOD, COD, TSS, TDS and pH
You cannot choose a treatment process without knowing five numbers. These are what your lab report and your consent letter talk about.
| Parameter | What it tells you | Why it matters for design |
|---|---|---|
| BOD (Biochemical Oxygen Demand) | Oxygen bacteria need to break down organic matter | Sizes the biological stage |
| COD (Chemical Oxygen Demand) | Total oxidisable organic and chemical load | Shows how heavy and how toxic the stream is |
| TSS (Total Suspended Solids) | Solids that settle or float | Sizes screens, clarifiers and filters |
| TDS (Total Dissolved Solids) | Dissolved salts | Decides if RO, evaporation or ZLD is needed |
| pH | Acidity or alkalinity | Needs neutralisation before biology |
The BOD/COD ratio is your first filter. A ratio above 0.5 means that the effluent is easily biodegradable. Thus, biological treatment works well. Between 0.3 and 0.5, the effluent is partly biodegradable, and bacteria will still have some trouble with the stream. Below 0.3, bacteria will have a lot of trouble. If this is your situation, you can read our guide on how to lower the BOD and COD in your industrial wastewater.
To illustrate the magnitude of the range, some effluent streams that Deur Water, a product of rudhra industries, designs for include COD above 120,000 mg/L, BOD above 40,000 mg/L, and TDS above 40,000 mg/L with a pH as low as 2. A stream like that and a rinse water stream with COD of 400 mg/L require completely different treatment plants, even though both are called industrial wastewater.
Stages of Industrial Wastewater Treatment, Step by Step
Most industrial effluent treatment plants (ETPs) remove easy-to-treat contaminants first, then hard-to-treat ones, and then polish the wastewater. Finally, they manage the sludge generated in the process. The following outlines this flow with typical design justifications.
Stage 1. Preliminary treatment: screening, oil removal and equalisation Bar screens remove plastics, rags, and fibres. Oil and grease traps remove free oil. An equalisation tank then blends the flow and load. This is the most undersized stage in Indian plants. Batch production and cleaning cycles create pH and load spikes and without sufficient 6 to 12 hour equalisation volume, the downstream biology gets shocked and fails.
Stage 2. Primary treatment: This stage adjusts pH and adds coagulants and/or flocculants. The addition of these chemicals cause the binding of fine and colloidal particles to larger particles to form flocs which settle in a clarifier or float in a dissolved air flotation (DAF) unit. This step removes the largest part of the suspended solids, as well as oil and a portion of the COD. In metal bearing streams, they are also precipitated out.
Stage 3. Secondary treatment: Biological Microorganisms consume dissolved organic matter and convert it to biomass, carbon dioxide and water. Some methods of doing this are activated sludge, moving bed biofilm reactor and sequencing batch reactor. Biological stages usually remove between 85 and 95 percent of BOD. The biomass is then separated in a secondary clarifier.
Stage 4. Tertiary treatment: polishing Multigrade filtration (MMF), activated carbon filtration (ACF), ultrafiltration, disinfection or advanced oxidation take the water to final discharge quality, or to the quality needed for reuse.
Stage 5. Sludge handling Every stage creates sludge. It is thickened, dewatered (filter press, centrifuge or decanter) and disposed of as per rules. Sludge from some industries is classified as hazardous waste, so this is a compliance item, not a footnote.
Stage 6 (where required). ZLD: reject management If discharge is not permitted or TDS is very high, RO concentrates and evaporators with crystallisers recover water and leave only solids.
The standard configuration of the Flow Deur Water, a product of Rudhra Industries, comprises equalisation and screening, physico-chemical treatment, biological treatment (ASP, MBBR or SBR as applicable), secondary clarifier, and filtration. The exact train is not assumed from your effluent analysis, but determined from it. after primary, after secondary, after filtration and treated water. Alt text: Actual sample showing effluent at each stage of treatment]
Treatment Methods: Physical, Chemical and Biological
The stages above use three families of methods. Being familiar with them will assist reading a proposal critically.
Physical methods separate without changing the chemistry: screening, sedimentation, flotation, filtration and membranes. They are low-risk and low chemical but shift pollutants around rather than destroy them.
Methods that change the pollutant include neutralization, coagulation and flocculation, chemical precipitation and oxidation (chlorine, ozone, Fenton and peroxide). They are commonly used to treat polluted, colored or toxic and/or non-biodegradable streams that bacteria cannot and typically add chemical costs and sludge.
Biological methods use microbes. This is a good way to treat water. Aerobic processes, which use oxygen, work well when the stream has an amount of waste. Anaerobic processes, which do not need oxygen, are best for very high‑strength organics because they need power and can produce useful biogas. Most treatment plants use both kinds of processes: anaerobic to handle most of the waste and then aerobic to polish the water.
You will see that biology is the way to remove one kilogram of COD but only when the effluent is biodegradable and not toxic. Chemistry and oxidation steps are used to make a stream biology‑friendly not to replace biology entirely.
Treatment Technologies Compared: ASP, MBBR, SBR, MBR and UASB
This is the comparison engineers and procurement teams actually ask for. Values are typical ranges and depend on design and effluent.
| Technology | How it works | Typical BOD removal | Footprint | Energy use | Best suited for |
|---|---|---|---|---|---|
| ASP (Activated Sludge) | Suspended biomass in an aerated tank, with sludge recycle | 85-95% | Large | Medium to high | Steady, medium-load streams with available land |
| MBBR (Moving Bed Biofilm Reactor) | Biomass grows on floating media | 85-95% | Compact | Medium | Space-limited sites and fluctuating loads |
| SBR (Sequencing Batch Reactor) | Fill, react, settle and decant in one tank | 85-95% | Compact | Medium | Batch-type industries, flexible and automated plants |
| MBR (Membrane Bioreactor) | Biology plus membrane filtration | 95%+ | Very compact | High | Reuse-grade water and tight space |
| UASB (Upflow Anaerobic Sludge Blanket) | Anaerobic granular sludge, no aeration | 60-80% COD | Medium | Low (can yield biogas) | High-strength organic streams (food, distillery) |
How to read this table.
MBBR and SBR are popular for Indian factories because they are compact, forgiving of load swings and easy to containerise. ASP is proven where land is available and flows are steady. MBR gives the best water quality but costs more to run. UASB is excellent as a first step for high-COD organic effluent, followed by aerobic polishing. Deur Water, a product of rudhra industries, designs ETPs around ASP, MBBR or SBR as the effluent analysis demands. For the others, we cover them here so you can compare options fairly. MBBR vs SBR guide
Advanced Treatment: Filtration, RO, Evaporation and ZLD
When conventional treatment is not enough, either because the discharge norm is tight, the water is to be reused or the TDS is high, advanced steps take over.
• Filtration (MMF and ACF) removes residual solids, colour and organics after the clarifier.
• Ultrafiltration and reverse osmosis remove fine particles and dissolved salts, producing water that can go back to process, cooling or boiler feed.
• Advanced oxidation (ozone, Fenton, UV-peroxide) breaks down persistent organics that survive biology, common in pharma and dye streams.
• Evaporation and crystallisation (multiple-effect evaporators, ATFD and crystallisers) handle the RO reject, so water is recovered and only salts remain.
ZLD is required by regulators for some industries, zones and sensitive water places according to CPCB and SPCB rules and court orders. People sometimes choose ZLD on their own when fresh water is scarce or when it is hard to get a discharge licence. ZLD is not a way to follow the rules. ZLD uses a lot of energy. It creates salt that must be disposed of safely so the decision to use ZLD must be backed by your regulatory situation or, by your water cost analysis. Check the conditions of your permit. Speak with your SPCB before you decide to go ahead. ZLD guide.
If you want to compare reuse versus discharge for your plant, our engineers can run the numbers during a free assessment. https://rudhraindustries.com/ free-assessment
Industrial Wastewater Treatment by Industry
Every industry fails in a different way. These are the patterns we see most.
Textile and Dyeing. The issues are color, high TDS from salt and soda changing medium COD. A normal process includes equalization, coagulation and flocculation biological treatment, color removal, by oxidation or carbon, RO and evaporation where ZLD is used. textile treatment guide, when published, ETP cost for textile industry.
Pharmaceuticals.I see that streams carry solvents, COD, salts and sometimes biologically active residues. Treatment often combines segregation at source, -treatment or oxidation anaerobic and aerobic biology and membranes plus evaporation. pharma wastewater guide, when published
Chemicals and petrochemicals. Extreme pH, toxicity and high TDS are the norm. Neutralisation, precipitation, oxidation and strict stream segregation come before any biology.
Food, dairy, beverage and distilleries. Very high BOD, fats and seasonal loads. DAF or fat traps, anaerobic treatment for the heavy load and aerobic polishing work best.
Electroplating and metal finishing. Heavy metals, cyanide and acidity need chemical precipitation, pH correction and filtration, often with RO for water recovery.
Paper and pulp, steel and general manufacturing.Fibres, colour, oils and high solids need first‑stage cleaning and tough sludge handling.
Segregation is the lesson. Segregation keeps toxic or high‑TDS streams separate, from large dilute ones; segregation treats each stream properly. Segregation always reduces the size and cost of the whole plant.
How to Choose the Right Treatment System
Buyers often start with a technology name. Start with these seven questions instead.
1. What exactly is in the effluent? Get a full lab analysis (COD, BOD, TSS, TDS, pH, oil, metals, colour) across different production days, not one sample.
2. What is the flow, and how variable is it? Average, peak and batch discharge all matter.
3. What must the outlet meet? Your CTO limits, or the quality needed for reuse.
4. Is ZLD required or optional? Confirm with your SPCB before designing for it.
5. How much space do you have? Tight sites favour MBBR, SBR or containerised systems.
6. What automation and operator skill level can you support? A well-designed plant that no one can run will fail.
7. What is the lifetime cost? Compare power, chemicals, manpower, sludge disposal and membrane replacement, not just the purchase price.
Containerised or civil-based? Containerised plants (5 to 500 KLD) install quickly, are compact and are movable, which suits small and mid-size units and sites with fast timelines. Civil-based plants (5 KLD to 1 MLD and above) suit large volumes and complex effluents. Our engineers design either, and we recommend based on your effluent and site, not on what is easier to build.
Red flags in a proposal: no effluent analysis requested, a fixed design offered before any testing, no mention of sludge handling, and a guarantee with no stated inlet values.
Cost of Industrial Wastewater Treatment in India
We do not quote a price per KLD in a guide like this because a number without your effluent data would mislead you. Costs vary widely for reasons you can control or, at least predict.
• Effluent strength: COD, TDS and toxicity drive the number of stages
• Capacity and peak flow: equalisation and tank volumes scale with it
• Technology choice: MBBR, SBR, MBR and ZLD differ in capital and running cost
• Construction type: containerised versus civil-based, and the material (MS, SS or FRP)
• Automation level: manual, semi-automatic or fully automatic
• Reuse or ZLD scope: RO, evaporators and crystallisers add significantly
• Operating cost: power, chemicals, manpower and sludge disposal over 10 to 15 years
We don't give one price for each KLD in a guide like this because a number without your wastewater data would confuse you. Expenses change a lot because of things you can manage or, at least expect:
Common Problems and How to Fix Them
Most plant failures are predictable. If your ETP is already running, this table may save a call to the vendor.
| Symptom | Likely cause | Typical fix |
|---|---|---|
| High COD or BOD at outlet | Shock load, low oxygen, toxic inflow or too little biomass | Improve equalisation, check DO and F/M ratio, segregate toxic streams |
| Foaming in aeration tank | Surfactants, oils or young sludge | Control inflow, adjust sludge age, use anti-foam only as a stopgap |
| Sludge bulking (poor settling) | Filamentous growth, low DO, nutrient imbalance | Correct DO, add nutrients, adjust return sludge |
| Strong odour | Anaerobic pockets, poor aeration or sludge handling | Improve mixing and aeration, cover and treat sludge area |
| Residual colour | Dye or oxidation-resistant compounds | Add oxidation or carbon polishing |
| High TDS at outlet | Salt load not removed by conventional treatment | Consider RO and evaporation or source reduction |
| Frequent chemical overdosing | Variable inflow without automation | Add pH and flow-based dosing control |
For deeper COD problems, see our guide on reducing BOD and COD in industrial wastewater.
Why Industries Choose Deur Water a product of rudhra industries
Industrial customers do not buy a tank. They buy a plant that passes inspection, runs reliably and does not become a headache in year three. That is how our team works.
• Problem-first approach: we study your site, water source and effluent before proposing a design.
• Experience: in water and energy engineering since 2014, with 1,000+ installations across 9 states in India.
• Range: ETP, ZLD, STP, RO, UF, DM and water treatment plants, plus operations and maintenance.
• Flexible formats: containerised ETPs from 5 to 500 KLD and civil-based plants from 5 KLD to 1 MLD and above.
• One team: consult, design, fabricate, install and commission, then operate, maintain and service.
Not sure what your effluent needs? Start a free assessment by sharing your water test report, or request a callback and an engineer will contact you. You can also see how our effluent treatment plants are configured.
Frequently Asked Questions
Q1: What are the methods of industrial wastewater treatment?
Ans : The three main families are physical, chemical and biological. The physical family includes screening, sedimentation, filtration and membranes. The chemical family includes neutralisation, coagulation and oxidation. The biological family includes anaerobic processes. Most plants combine all three families. They add evaporation or crystallisation when zero liquid discharge is required.
Q2: What are the stages of industrial wastewater treatment?
Ans : There are five main stages: preliminary treatment (screening and equalisation), primary treatment (physico-chemical), secondary treatment (biological), tertiary treatment (filtration, polishing) and sludge handling. ZLD adds a sixth step to recover water from reject streams.
Q3: What is the difference between ETP and STP?
Ans : An ETP deals with waste, which changes a lot and can have chemicals, metals or a lot of salt. An STP handles home waste, which's mostly from people and easier to predict. Lots of factories need both kinds of systems: an ETP for the water used in their work and an STP for the waste, from the people who work there.
Q4: How is COD reduced in industrial wastewater?
Ans : COD can be lowered by separating streams by using coagulation or oxidation when the waste is not biodegradable and, by applying biological treatment first anaerobic then aerobic, for the biodegradable part. Then filtration or carbon polishing takes away the remaining COD.
Q5: When is ZLD mandatory in India?
Ans : ZLD is required for sectors, clusters and water bodies, under CPCB and SPCB directions and court or tribunal orders. You should check your consent conditions. Confirm with your State Pollution Control Board before designing for ZLD.
Q6: How do I choose the right treatment technology for my plant?
Ans : Start with an analysis of the effluent then look at flow discharge or reuse targets, space, automation and lifetime costs in relation to the options. MBBR and SBR work well for sites ASP is good for consistent flows when there is space and ZLD is the right choice when there are high-TDS or no-discharge needs.
Not Sure What Your Effluent Needs?
Share your water test report and our engineers will review your effluent, discharge norms and site conditions, then recommend the right approach, whether that’s a new ETP, an upgrade to your existing plant, or ZLD. No fixed designs before testing, and no obligation.
Since 2014, Deur Water, a product of rudhra industries has completed 1,000+ installations across 9 states.
Get a Free Assessment → https://rudhraindustries.com/free-assessment
Request a Callback → tel: +91 9980000014
Conclusion: Start With Your Effluent, Not a Technology
Industrial wastewater treatment is not one machine or one process. It is a series of stages designed around what your effluent contains, how much of it you produce, and what your consent letter or reu
The plants that work for years have a few things in common:
- They start with data. A full effluent analysis across different production days comes before any design.
- They respect the basics. Adequate equalisation and stream segregation prevent most failures.
- They match the technology to the stream. ASP, MBBR, SBR, MBR or UASB is chosen for the effluent, not from a catalogue.
- They are judged on lifetime cost. Power, chemicals, sludge disposal and manpower over 10 to 15 years matter more than the purchase price.
Get these right, and your ETP becomes more than a compliance cost. It becomes a source of reusable water and one less thing to worry about during an SPCB inspection.
Explore Our Wastewater Treatment Guides
This guide gives you the full picture. For deeper answers on specific topics, read:
- How to Reduce BOD and COD in Industrial Wastewater
- Our Effluent Treatment Plants: Containerised and Civil-Based ETPs
Industrial Wastewater Treatment · Effluent Treatment Plant (ETP) · Wastewater Treatment Process · ZLD (Zero Liquid Discharge) · BOD and COD Reduction · MBBR · SBR · Textile Effluent Treatment · Pharma Wastewater Treatment · CPCB Discharge Standards

